← Back to SaniDate 5.0 product overview
SaniDate 5.0 is used to control bacteria and non-public health microorganisms that cause decay and spoilage. It is applied through fogging on indoor hard, non-porous surfaces, as a foam treatment on vertical and irregular surfaces, or as a liquid for treating drinking water, watering lines, membranes, filters, and food processing equipment. When used on food contact surfaces, it should be followed by a potable water rinse before re-use.
| Target pest | Location | Rate | Unit | Dilution | Label notes |
|---|---|---|---|---|---|
| non-public health microorganisms that cause decay and spoilage | Indoor | 1 fl. oz. | gallon | 1:128 | Fogging (Dairy, Beverage, Food Storage Facilities, Packing Houses and Food Processing Plants). All surfaces must be thoroughly pre-cleaned prior to fogging. Food products and food packaging materials must be removed or covered with waterproof coverings. Vacate all personnel from the room during fogging and for a minimum of 1 hour after fogging. Ventilate buildings, coops, and other closed spaces for minimum of one hour. Allow surfaces to drain thoroughly before operations are resumed. Any food contact surfaces must be rinsed with potable water prior to re-use. |
| Foaming Applications: Apply SaniDate 5.0 as a foam treatment for the non-pesticidal purpose of cleaning hard, non–porous surfaces, and to enhance contact on hard, non-porous surfaces, vertical surfaces and irregular surfaces such as metal grating and structural steel where contact is difficult to maintain with coarse spray treatments. Add a foaming agent to the spray tank that contains the diluted SaniDate 5.0 solution. Apply foam until the surface treated is completely covered. Allow foam treated surface to air dry. Any food contact surfaces must be rinsed with potable water prior to re-use. |
| Target pest | Rate | Unit | Label notes |
|---|---|---|---|
| bacteria | 0.85-1.27 fl. oz. | 100 gallons | Treating poultry, swine, livestock watering operating systems when animals are present. Use low rate when applying for more than 5 consecutive days. |
| Target pest | Rate | Unit | Dilution | Label notes |
|---|---|---|---|---|
| bacteria | 2.5 fl. oz. | gallon | 2% solution (1:50) | Rapid cleaning applications. Circulate or hold solution in the system for 3 to 6 hours depending on conditions. Following the cleaning process, thoroughly flush systems with potable water to remove product out of the entire system including nipples or cups. |
| Rate | Unit | Label notes |
|---|---|---|
| 0.1 fl. oz. | 1 gallon | Direct disinfection. Within a pH range of 3-7 and maximum water temperature of 80 degrees F. Allow the membranes to soak for a minimum of 10 minutes. Flush or rinse membranes with clean water after treatment. |
| 0.5 fl. oz. | 5 gallons | Direct disinfection. Within a pH range of 3-7 and maximum water temperature of 80 degrees F. Allow the membranes to soak for a minimum of 10 minutes. Flush or rinse membranes with clean water after treatment. |
| Rate | Unit | Label notes |
|---|---|---|
| 2.5-10.25 fl. oz. | 100 gallons | Within a pH of 3-7. Thoroughly flush systems with potable water to remove product out of the entire system including nipples or cups. |
| Rate | Unit | Label notes |
|---|---|---|
| 2.5-10.25 fl. oz. | 100 gallons | Clean in place (CIP) applications involving filters. Re-circulate solution for a minimum of 10 minutes. Upon completion of cleaning cycle, flush filter housings and/or assemblies with clean water. |
| Rate | Unit | Label notes |
|---|---|---|
| 1-6 fl. oz. | gallon | Alkaline detergent cleaning supplement. All hard, non-porous food contact surfaces treated with this detergent must be thoroughly rinsed with potable water followed by a sanitizing step with an approved food contact surface sanitizer (such as SaniDate 5.0). |
| For pests | Amount | Per | Finished strength | Label notes |
|---|---|---|---|---|
| bacteria | 5-8 fl. oz. | 5 gallons | 1:128-1:80 | To apply using a standard medicator, make a stock solution. Do not mix SaniDate 5.0 with other product in the same stock solution. Set metering pump at 1 oz. of stock solution per 1 gallon of water (1:128). |
| non-public health microorganisms | 1 fl. oz. | gallon | 1:128 (460 ppm of peroxyacetic acid) | Fogging: 1 quart per 1,000 feet of room area. |