Chemicals › biosafe › sanidate-16-0-wwt

SaniDate 16.0 WWT

BioSafe · Hydrogen Peroxide · EPA Reg 8743-19-70299 · Insecticide Document last checked 2026-05-30

About this product

Active ingredient Hydrogen Peroxide
Manufacturer BioSafe
Category Insecticide

Full details for SaniDate 16.0 WWT

Source product label ↗ Open the catalog source label while the local copy is reviewed. Verify the product name, EPA registration number, and revision before use. Source safety data sheet ↗ Open the catalog source SDS while the local copy is reviewed. Verify the exact product and revision before relying on it. EPA registration data Reg. 8743-19-70299 — registry reference, signal word and status.

Applicator discussion

Nothing here is label direction — the label is the law. These are notes from other applicators, moderated before they appear. Check the labeling accompanying the product and applicable state requirements.

Add your experience

Sign in through the portal or Create a free account to post. Comments are reviewed before they appear. Need a website for your pest-control business? See site plans.

According to the label From the product label

These details were extracted from this product's label PDF. The label is the law. Confirm every rate, site, restriction and safety requirement against the label before mixing or applying. Check for a state supplemental label; a product may be restricted or prohibited in a state or site even when a rate appears below. · EPA registration data for Reg. 8743-19-70299 →

SaniDate 16.0 WWT is a peroxyacetic acid-based antimicrobial agent used for controlling bacteria, fungi, clams, oysters, and other aquatic invertebrates. It is specifically formulated for use in manufacturing processes involving paper, pulp, and paperboard, as well as in water systems such as cooling towers, evaporative condensers, air washers, and recirculating water systems. The active ingredients are Hydrogen Peroxide (22.8%) and Peroxyacetic Acid (16.2%). The product can be applied as a continuous feed or via shock dosing depending on the specific water system and infestation level. When used in influent water systems, it helps maintain microbiological control. Users should be aware that the product is corrosive; it must be handled with appropriate personal protective equipment, including long-sleeved shirts, long pants, rubber gloves, and eye protection. It is also important to note that the product is not for use in dietary applications or for direct contact with food/drink. Always follow specific dilution and mixing instructions for the target application to ensure efficacy and safety.

Pests covered (1)
bacteria, fungi, clams, oysters, and other aquatic invertebrates
Areas treatable (1)
Paper, pulp, and paperboard manufacturing; cooling towers, evaporative condensers, air washers, and recirculating water systems

How to treat each type of area 1

Paper, pulp, and paperboard manufacturing; cooling towers, evaporative condensers, air washers, and recirculating water systems

Target pest Location Rate Unit Dilution Label notes
bacteria, fungi, clams, oysters, and other aquatic invertebrates Both Varies by application oz. See mixing instructions Not for use in dietary applications or for direct contact with food/drink.

Mixing instructions 3

For pests Location Amount Per Label notes
Microbiological control in influent water systems Indoor 0.1-1.82 fl. oz. Based on 1,000 gallons of process water; dosage is 0.1-1.82 fl. oz. per 1,000 gallons.
Shock dose for water systems Indoor 0.8-1.28 lb. (dry basis) per 1,000 gallons Dosage is 0.8-1.28 lb. per 1,000 gallons of process water.
Continuous dosing for water systems Indoor 1.4-5.0 fl. oz. per 1,000 gallons Used to maintain microbiological control.

Worker safety

PPE required Long-sleeved shirt, long pants, rubber gloves (barrier laminate or butyl rubber, nitrile, or neoprene), chemical resistant footwear, eye protection (goggles and face shield), and NIOSH-approved respirator with organic vapor (OV) cartridge and N95 or P100 filter if required.

Use restrictions 4